Avantone Mixcube Active Studio Monitor, Butter Cream (Single) - Nearly New

Full Description

Crisp Audio

The Avantone Mixcube Active Studio Monitor is constructed from thick MDF board to provide a high-rigidity, low-resonance cabinet. The 5.25" LF Driver produces a crisp, punchy sound from such a compact sized monitor. With a frequency response of 90 Hz - 17 kHz, the Avantone Mixcube Active Studio Monitor can handle a wide range of audio.

Magnetic Shielding

This full-range mini reference monitor is also magnetically shielded, which means you can place them in the ideal location on your desk without the risk of interference. With the Avantone Mixcube Active Studio Monitor, you can hear what your mix sounds like when played back over small “bass-challenged” systems such as televisions, clock radios, computers, car stereos.

REAR PANEL CONTROLS/CONNECTIONS

• BALANCED INPUT: This "combo XLR" input accepts a BALANCED male XLR plug as well as a 3-conductor BALANCED TRS ¼" or a 2 conductor UNBALANCED TS ¼" male plug. For unbalanced operation with a TS connector the minus signal is automatically grounded.
• SYSTEM GAIN: This variable control adjusts the sensitivity of the signal that appears at the input. Rotating the control clockwise increases the sensitivity while a counter-clockwise rotation decreases sensitivity. The adjustable gain range is from -30 to +6 dB. A setting of +6 allows a full, unimpeded signal to be sent to the amplifier. The detented gain positions allow for repeatable settings between speakers for proper matching. Please Note: when the signal appearing at the input is too hot, the amplifier can overload causing distortion and possible damage to the speaker. If overload occurs, attenuate (decrease) the input level by turning the knob counter-clockwise a few clicks.
• ON/OFF Switch: This illuminated switch turns the amplifier section on and off. The unit is still receiving power from the transformer however.
• AC INPUT: This input is only to be use with the proprietary AVANTONE Power Supply. Tighten the cable/connector securely for reliable operation. Note: There is a switch on the power supply for selecting the proper AC/MAINS operating voltage for your location.
• GROUND LIFT Switch: By engaging this switch the pin 1 shield is lifted at the input jack. This can be used to aid in ground loop control of the incoming analog line signal.
• **PLACEMENT:*** When positioning the AVANTONE MixCubes on stands or console bridges it is best to keep them at ear level and slightly angled in towards the engineer. Since they are shielded it is ok to place them near a CRT video monitor or TV without causing any problems. The bottom mic stand mounts will also allow you creative positioning options in unusual studio playback situations.

Features

• Active (self-powered) shielded full-range single speaker
• Convection/heat sink-aluminum fins
• Designed to be high resolution
• All cabinet edges are radiused
• Elegant polyurethane high gloss butter-cream finish
• 7mm thick neoprene pad embedded into the base of the cabinet serves as a skid-resistant acoustic isolator
• The cloth surround material is made in Japan and has unique damping characteristics, enabling a predictable compliance over the lifespan of the driver
• 5.25" die-cast aluminum frame supports the driver/cone minimizing mechanical transfers
• The outer mounting face of the aluminum frame is polished for an elegant appearance

Specifications

• SYSTEM TYPE: Active shielded full-range stereo speaker
• FREQUENCY RESPONSE: 90hz-17,000hz (Accessible Musical Range)
• DRIVER IMPEDANCE: Nominal 8 Ω
• MAX SPL: 104db 1 meter @ 1 THD (PINK NOISE)
• AMPLIFIER: Class A/B
• AMP POWER: 60 watts RMS@ .005 THD (1KHz)
• AMP FREQ. RESPONSE: 22Hz-50KHz +0dB/- 3dB (90Hz-50KHz +/-0dB)
• NOISE: S/N -113 dB
• SENSITIVITY: 0dBu (.775VRMS) input at maximum volume (+6dB) = 104dB SPL
• COOLING: Convection / Heat Sink-Aluminum Fins
• DRIVER: Proprietary Design 5.25" Cast Aluminum Frame / Paper Cone/Shielded
• CABINET: Sealed design / 18mm MDF / Dacron acoustical stuffing
• INPUTS: XLR & TRS (COMBO JACK) +4/Balanced and -10 unbalanced
• CABINET DIMENSIONS: 165mm X 165mm X 165mm ( 6 1/2" x 6 1/2" x 6 1/2" )
• CABINET WEIGHT: 7Lbs 2 oz / 3.55 kgs (per speaker)